Home > Kirby > Parts > Kirby Sentria parts > Floor Nozzle Asm >

Aftermarket Kirby Brush Roll G5 through Avalir - FIRM
Aftermarket Brush Roll Kirby G5 G6 UG Sentria


 
Our Price: $22.49


Product Code: K-PRT-FLNZ-AFT152505
Qty:

Description
 
AFTERMARKET KIRBY VACUUM BRUSH ROLL ASSEMBLY
(firm bristles)
These brush rolls are high quality aftermarket wooden brush rolls. They also have the height adjustment, just like the genuine ones.
This is the type of the beater brush that comes installed in the new Kirby sweepers sold by Kirby dealers

Will fit following Kirby "Generation" models:
  • Generation 3 (G3)
  • Generation 4 (G4)
  • Generation 5 (G5)
  • Generation 6 (G6)
  • Ultimate G (G7 or UG)
  • Ultimate G Diamond Ed.(G7 or DE)
  • Sentria (G10)
  • Sentria II (Sentria 2)
  • Avalir
  • Avalir 2
Replaces OEM Part # 152505
This brush roll will fit in the nozzle that has indicator light on the right (if you standing behind the vacuum as if you were vacuuming). It will fit in ANY Generations nozzle but if light is not on the right it will not be lit when brush is spinning.

HOW TO - V I D E O S

How to change / replace Kirby vacuum cleaner brush roller (a.k.a. beater bar)
Video is for belt replacement but procedure is the same.
About 3 Kirby roller positions go HERE:




KNOWN ISSUES:
Customers email:
Almost exactly a year ago.. and last week I realized the bearings on the white ended side are frozen solid. Do you have some sort of warranty program? I replaced the original OEM brush with this one from you, and I think it's safe to say the OEM one was still spinning some 35 years later, while yours seems to have died a premature death.
Our response:
We give one year guarantee ONLY for complete units. No parts, supplies or components are covered. However even in that case unit warranty would not have covered belts, bulbs, wheels and the roller. Manufacturer does not warranty them either. This is a bit premature – you are right, but this most likely have happened because something got caught around the bearing or cap and friction heated up the end of the roller and it just froze. There is nothing I can even suggest to make 100% sure that this would not happen again. In general it is highly recommended to keep the roller free of hair and threads from carpet but some may get in where you would not be able to even see.


*This is a generic product designed and manufactured by Brushroll.com for aftermarket replacement. The KIRBY® logo and brand are registered trademarks by KIRBY®. This is not an original equipment item and is not covered under the KIRBY® manufacturer warranty. Use of the KIRBY® brand or item numbers are only used to exhibit compatibility.*



WARNING: This product can expose you to chemicals including Di (2-ethylhexyl) Phthalate (DEHP), which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Kirby > Parts > Kirby Sentria parts > Floor Nozzle Asm
Kirby > Parts > Kirby Ultimate G Diamond Ed. Parts > Floor Nozzle Asm
Kirby > Parts > Kirby G5 parts > Floor Nozzle Asm
Kirby > Parts > Kirby G6 parts > Floor Nozzle Asm
Kirby > Parts > Kirby Ultimate G parts > Floor Nozzle Asm
Kirby > Supplies > Brush Rolls and Belts
Kirby > Parts > Kirby Sentria II parts > Floor Nozzle Asm
Kirby > Parts > Kirby Avalir parts > Floor Nozzle Asm
Kirby > Parts > Kirby Avalir 2 parts > Floor Nozzle Asm