Rainbow Black Nozzle R14350 Modified to fit e and older E2 220v

Home > Miscellaneous > LANDING > Rainbow 220 / 230 / 240 volt parts >

NEW design Modified for E and E2 220 volt

Rainbow Black Nozzle R14350 Modified to fit e and older E2 220v

Alternative Views:

Our Price: $310.96

Product Code: R-ACC-R14350_MODIFIED_220V

Qty:

Description

New design BLACK E2 series Rainbow vacuum nozzle
220 / 230 / 240 volt !

MODIFIED to fit:
E series Rainbow vacuum (1 speed )
E2 series Rainbow vacuum ( 2 speed GOLD )
E2 series Rainbow vacuum ( 2 speed PLATINUM / SILVER / BLUE )

Since the cord has been installed it will no longer work with BLACK Rainbow model that came out May 2011

This design has been out there since May 2011 when new Rainbow E2 BLACK model 12 came out.
Nozzle is very air tight thus not loosing any suction due to gaps between parts. So whatever airflow is generated by the vacuum motor is all put to work

Design

	Much larger bumper to save your protect your furniture. Bright LED headlight for dark corners. Rotating edge brushes. It is very well insulated / sealed construction so no more loss of suction through structural gaps that were inevitable in prior design.
	If you have ever seen another Rainbow vacuum you may notice that it looks totally different from the bottom. Bottom plate covering brush roller and the belt is latched onto the nozzle in 4 places and then it is locked by a small plastic dial near the right wheel. Wheels covered with rubber or rubber-like material making them safe on hard surface floors. In the front of the nozzle you see round edge brushes on each side and YES they are spinning and brushing towards the center of the nozzle while you are vacuuming. As spare part these round brushes are available with longer or shorter bristles. All parts just snap together and is held with tabs. Only screws used in the entire assembly (not counting motor) are ones in the center of the edge brushes. Well thought through design that is very easy to take apart and put back together. There are no front wheels anymore but the edge brushes and brush roll bristles keep the bottom of the nozzle above the hard surface floors so it is safe using it hardwood floor as the plastic bottom would not touch it. When nozzle is on the carpet bristles sink into the rug by a fraction of an inch bringing intake closer to the rug. Belt is 3/16 of an inch wider than regular Rainbow belt but seems to be the same diameter and made out of the same material. It may be wider because with side edge brushes it needs a bit more torques and it may result in need to replace regular belts more often than the new wider belt. Bristles on the both sides of roller are positioned at different angle. This may be done to reduce nozzle jumping over a carpet. no more switching tools in order to get edges of the rug vacuumed.
	Rotating brushes get the momentum from the worm-gear on each end of the wood brush roller spinning gear with attached to it circular edge brush. Worm-gears have opposing threads so both edge bristles are spinning opposite direction brushing towards the center of the nozzle.
	Circuit board with 9 LED micro lights. Power to the motor is supplied through the board but this is probably to just to eliminate the need for extra harness, plugs and terminals. Nozzle motor is still using the same power as in your house electrical outlets.
	ONLY part that remains the same as in prior model Rainbow vacuum nozzle. Noise dampening - 2 rubber rings that go on around the motor and one rubber boot that is placed in the front of the motor when installing in the nozzle. This will reduce the vibration passed onto the nozzle assembly so nozzle will be less noisy.
	Pivot arm - it has built in swivel that swivels 180 degrees. Built in wand release (light gray part in the picture) - you do not have to bend down to release the wand from the pivot. All you have to do now id press the pedal with your foot and it will release the wand so you can pull it out
	And last but not least - bottom cover portion that forms the intake compartment housing the bush roller goes 1/4 of an inch into the main housing making sealing it off. There plenty of space for dust bunnies to go through so it is very unlikely to clog.

Disclaimer:
We are not affiliated with Rexair, Inc. - no factory warranty. This Rainbow vacuum carpet nozzle is still covered under our guarantee.

WARNING: This product can expose you to chemicals including Di (2-ethylhexyl) Phthalate (DEHP), which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Miscellaneous > LANDING > Rainbow 220 / 230 / 240 volt parts

	Kirby G4 Handle Cover
	Rainbow Screw Baffle and Cap E $1.58
	Kirby Motor Housing $13.77
	Rainbow Aquamate III pedal 3 position $2.32
	Rainbow Fan Spacer TOP D4/SE