Kirby motor 110volt

Home > Kirby > Parts > Kirby Avalir parts > Motor Asm >

Kirby Motor 110 Volt

Alternative Views:

Our Price: $179.00

Product Code: K-PRT-MOTR-101396G

Qty:

Description

KIRBY VACUUM MOTOR ASSEMBLY

Fits following Kirby sweeper models:

Generation 3 (G3)
Generation 4 (G4)
Generation 5 (G5)
Generation 6 (G6)
Ultimate G (G7 or UG)
Ultimate G Diamond Ed.(G7 or DE)
Sentria (G10)
Sentria II (Sentria 2)
Avalir
Avalir 2

Kirby Ultimate G Diamond Edition sweeper owners please contact us before making a purchase so we could install a two speed switch.

This does not come with any gear, If you can not reuse gears that you have, we suggest you to buy GEAR SET.

EXPORT
This is 110 volt Kirby motor for use in countries that have 110 volt supply (such as USA, Japan..) If you are interested in 220 volt motor - we may have them. Simply go to main Kirby page or SEARCH the store for "220volt".

Part # 101396

( 101396 )

TIPS ON INSTALATION:

When taking old motor out snap as many pictures as possible to remember how to put everything back together. There are numerous help articles and we have a few on our own but you would feel better that you personally may forget so snap pictures. You can erase them all when you done (thanks digital photography).
Testing motor when not in housing is a bit dangerous. You need to press onto 2 levers and hold it at the same time and the fan blade would spin at 30000 RPM and it may get you fingers. Just install it into the housing before you plug it in.
When installed and all 4 screws tightened try spinning the shaft by hand. It should spin freely. If it does not - you need to loosen the screws and puch the motor to the front of the housing and tighten the screws again.
HERE you can fing how to get to the motor and from there you will just need to get the transmission out and 4 screws that hold the motor.
Look at 2 last pictures on this ARTICLE and make sure you have the piece that controls transmission installed right.
When motor is in and you want to check if it works before you finish assembling it see this ARTICLE and make sure that BOTH levers are pushed all the way in, otherwise motor will not run.

WARNING: This product can expose you to chemicals including Di (2-ethylhexyl) Phthalate (DEHP), which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Kirby > Parts > Kirby Avalir parts > Motor Asm
Kirby > Parts > Kirby G3 parts > Motor Asm
Kirby > Parts > Kirby G4 parts > Motor Asm
Kirby > Parts > Kirby G5 parts > Motor Asm
Kirby > Parts > Kirby G6 parts > Motor Asm
Kirby > Parts > Kirby Ultimate G parts > Motor Asm
Kirby > Parts > Kirby Ultimate G Diamond Ed. Parts > Motor Asm
Kirby > Parts > Kirby Sentria parts > Motor Asm
Kirby > Parts > Kirby Sentria II parts > Motor Asm
Kirby > Parts > Kirby Avalir 2 parts > Motor Asm

	Kirby Handle Lock Shaft/Pin (3CB/LII) $4.12
	Kirby Rear Axle retainer LEFT $0.33
	Kirby Sprayer Sentria II $15.04
	Kirby Bag Top Cover G3 $12.33
	Kirby Bag Top Cover UG/DE $8.76
	Kirby Tilt Latch Kit $3.68
	Kirby Handle Fork Spring $2.55