Home > Kirby > Parts > Kirby Sentria parts > Attachment Set (SE) >

Kirby Variable Speed Hose End G5 and up
Variable suction blower G5/SE
 
Alternative Views:
Our Price: $15.97


Free Shipping
Product Code: K-PRT-ATT-211397S
Qty:

Description
 
Kirby vacuum cleaner
Used to be maroon now available in black color only
VARIABLE SPEED SUCTION/BLOWER CONNECTOR

Kirby G3 and G4 models have a different gasket so this connector will not work.

How it works:
This is to be installed instead of the regular connector on the attachment hose.
ALL Kirby "Generation"series vacuums have 2 speeds. Lower speed is for vacuuming with the carpet nozzle attached to the unit and "high" - using attachment hose. Nozzle and hose simply press on different part of the safety switch that is in the front of the unit and this makes Kirby vacuum motor spin faster or slower.

This variable speed suction/blower connector has the pin that can be adjusted to press on the switch as if the nozzle would be attached so you can vacuum delicate things that may get damaged if vacuumed with Kirby running at "Full Throttle".

To replace:
Submerge the end into hot water (not too hot so you would be able to touch it) for about 30 seconds. The hose end will become soft enough to squeeze and get it out through the hole.

Matches Kirby Sentria color.
Fits Kirby Models:
  • Avalir II
  • Avalir
  • Sentria II (G10D)
  • Sentria (G10)
  • Ultimate G Diamond Ed.(G7D or DE)
  • Ultimate G (G7 or UG)
  • Generation 6 (G6)
  • Generation 5 (G5)

Kirby part number: 211397S

WARNING: This product can expose you to chemicals including Di (2-ethylhexyl) Phthalate (DEHP), which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov

Average Customer Review: Average Customer Review: 5 of 5 5 of 5 Total Reviews: 1 Write a review.

  0 of 0 people found the following review helpful:
 
5 of 5 Worthwhile extra October 8, 2025
Reviewer: KM from United Kingdom  
Highly recommend fitting this in place of the standard connector. On low speed, the Kirby still has plenty of suction (even runs the Zippbrush just fine), but with a lot less noise, making it much more pleasant to use. Kirby really should fit these as standard.

Was this review helpful to you?


Browse for more products in the same category as this item:

Kirby > Parts > Kirby Sentria parts > Attachment Set (SE)
Kirby > Parts > Kirby G5 parts > Attachment Set (G5)
Kirby > Parts > Kirby G6 parts > Attachment Set (G6)
Kirby > Parts > Kirby Ultimate G parts > Attachment Set (UG)
Kirby > Parts > Kirby Ultimate G Diamond Ed. Parts > Attachment Set (UGD)
Kirby > Parts > Popular Parts > Attachments > Kirby Attachment Hose
Kirby > Parts > Kirby Sentria II parts > Attachment Set (SE)
Kirby > Parts > Kirby Avalir parts > Attachment Set
Kirby > Parts > Kirby Avalir 2 parts > Attachment Set


Aftermarket Rainbow D4 SE Power Cord $20.79
Kirby Hose G4 $35.69
Kirby Suds Sprayer Cap G3/UG/DE $3.79
HM-400 Odor Control HEPA Pre-filter Wrap for Austin Air HealthMate Std. $26.52
Rainbow Screw, H566, #5 X .50 INCH $1.48
Kirby Avalir 2 Multi-Surface Shampooer $165.36
Kirby Hose Tube G3
Centurion Vision Safety Helmet Tinted Replacement Visor $18.71
Kirby Wand Sentria II $9.94